DIY quadcopter: FrankenDrone

Maiden of “FrankenDrone”,  DIY quadcopter

So far, managed to record video maiden (first flight) of my new “FrankenDrone”, DIY quadcopter. It has JJ1000 controller board, gears and propellers (props) from Syma X5C, with 7×20 mm motors.

Upgrading stronger motors

Now upgraded to FY326 gearbox and motors 8.5×20 mm. My flight with Mobius camera onboard failed because microSD card has some problem with deleted files. Camera showing that it recording, but I can’t find video files on microSD card. Now, after quick format, everything works fine. Here will be updated status of the experimental flights.

The difference between gearboxes of Syma X5C and FY326 Q7

Syma X5C, as well as its clone Bayangtoys X8 has some problem with vertical “play” of the main shaft which holds props. Gearbox with motor mount and prop mount has no such problem, or it is very minimal play, maybe 0.5 mm, while Syma X5C and Bayangtoys X8 has this “movement freedom” of about 1-1.5 mm. It is not a problem during flight, since props pulling this shaft up, and gears are aligned perfectly. But, noticed that gearbox from FY326 (original designation of this quadcopter is Q7) is more silent. On Syma X5C gearbox, I can clearly hear strange noise produced by movement of pinion and gears, while on gearbox from FY326, this noise is very low.

Further improvement

Gearbox has 3 x 3 mm square profile, but I found only 3 mm round aluminium rod, and used it. The problem with this rod is that aluminium by default is hard to drill – broke 3 drills and did not make hole for screw to fix it properly. Now found better option on Aliexpress, but so far… haven’t money to buy. It will be long(ish) waiting until it happens. 🙁

Excellent carbon square,  3 x 3 mm can be found here.

carbon_1

For more range & installing buzzer

I already modified JJ1000 remote with “V” antenna, and should to upgrade similar antenna on the quadcopter to get maximum possible range, since I want to fly it FPV. In order to avoid duplicate post, anyone interested in extending range, can found it on my webpage here. Note that diagram on this page is for Syma X5C, and Bayangtoys X8. On JJ1000 board, installing buzzer is much simpler:

quadcopter buzzer

Just solder +ve of the buzzer on cahtode of the diode, and -ve on drain of the MOSFET which run on/off LEDs on the quadcopter. After binding, buzzer whistling all the time, and then press right “shoulder” button for 3 seconds to turn LEDs and buzzer off. Battery alarm will sounds and LEDs will blinks. In the case of lost quadcopter, just turn of remote, and buzzer will sounds, LEDs will blinks. Easier to found.

Choice of the buzzer

At first model of my FrankenDrone, I am using buzzer from some programmable LEDs which has buzzer in between, but this option is bit expensive. Then ordered buzzers from Aliexpress – little one, just 0.67 grams. But it is big disappointment – not loud enough. Reason why I wanted so light buzzers is to install it on smaller quadcopters, but this one is big and has no such issue with little bit heavier buzzer. This one from Banggood.com is the best option:

buzzerBanggood

The rule about buzzer

For indoor flight, quiet buzzer is okay, but this makes no sense to install it when indoor flight – you always can find your quad. The louder the better. If it does not give you “instant headache” when sounds, it is not good for outdoor flight with quadcopter. Consider next situation: strong wind blows away your quadcopter, and it flyaway into some bush. The same wind may be sufficiently loud to “override” volume of some small and silent buzzers. So, louder is better. This one above is sufficiently loud, but I want more, still searching for cheap yet louder one. 🙂

Become my ‘permanent Banggood friend’ by applying this CODE if you already haven’t Banggood account. You will buy at no additional cost, and I will get some points which helps me to make more exciting projects. Thank you in advance.

6 thoughts on “DIY quadcopter: FrankenDrone”

    1. JJ1000 is already too heavy. Even small 4 grams camera I made is too heavy and drain battery too fast. Even modified (carbon frame) quadcopter this size is too weak to lift the camera. The problem is in small propellers which make more air drag than thrust. It is in theory possible, but flight may be too short, maybe one or two minute. Try attach something to it, say rubber eraser with similar weight between 4 and 8 grams. So you will get the answer right now.

  1. Hello, can I have a close-up picture of your Mobius camera + -Boscam FPV 5.8G 10mW Wireless Audio Video Transmitter Module TX5813-. I am having confusion on how to wire the transmitter and hook it up to my Mobius camera. Also which cables do I hook in http://i.imgur.com/YVRrcBo.jpg == the USB cable.

    Thanks 🙂

Leave a Reply

Your email address will not be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.